B-B18
| Removable Flash Disk 4GB for ZVA/ZVB with controller unit FMR7/3 or
FMR7/6 |
B-B18
| Removable hard disk 160GB (including firmware) for R&S® ZVA and
R&S® ZVB with FMR7 |
B-B4
| Oven quartz (OCXO) for ZVA, ZVB, ZVT |
B-K2
| Time domain (for ZVA, ZVB, ZVT) (software license) |
B-K30
| Noise figure measurement on 2 port devices (for ZVA and ZVT, |
B16
| Direct generator-receiver-access (for 2 port ZVA67) |
B21
| Generator Step Attenuator Port 1, mechanical, 50dB in 10dB steps |
B22
| Generator Step Attenuator Port 2, mechanical, 50dB in 10dB steps |
B23
| Generator Step Attenuator Port 3, mechanical, 50dB in 10dB steps |
B24
| Generator Step Attenuator Port 4, mechanical, 50dB in 10dB steps |
B31
| Receiver Step Attenuator Port 1, mechanical, 35dB in 5dB steps |
B32
| Receiver Step Attenuator Port 2, mechanical, 35dB in 5dB steps |
B33
| Receiver Step Attenuator Port 3, mechanical, 35dB in 5dB steps |
B34
| Receiver Step Attenuator Port 4, mechanical, 35dB in 5dB steps |
B7
| Measurements on pulsed signals. Pulse profile,Recording time up to
25ms, up to 30MHz bandwidth |
B8
| External attenuator control. Control unit for electronic
attenuators of ZVAZ90E, ZVA-Z110E |
C3
| Three years of calibration coverage based on the R&S
recommended calibration interval - includes test data. |
C3
| Three years of calibration coverage based on the R&S
recommended calibration interval - includes test data. |
C5
| Five years of calibration coverage based on the R&S recommended
calibration interval - includes test data. |
C5
| Five years of calibration coverage based on the R&S recommended
calibration interval - includes test data. |
DCV-2
| Documentation of calibration values |
DCV-ZP
| Printout of DCV (additional, in combination with DCV-Option only) |
K10
| Group delay measurement on converters without LO access. For long
distances via LXI network of 2 ZVA or ZVT. |
K17
| Increases the receiver bandwidth to 5MHz |
K27
| Two internal pulse generators (for ZVA and ZVT) |
K4
| Frequency converting measurement for ZVA and ZVT |
K5
| Phase measurement on mixers (for ZVA, ZVT; ZVA/T-B16 and ZVA-K4
required) |
K6
| True Differential Measurements for all 4-port ZVA and for ZVT with
at least 3 ports |
K7
| Measurements on pulsed signals pulse profile, recording time up to
3ms up to 30 MHz bandwidth |
K8
| Control of frequency converters (for ZVA with f>20 GHz, ZVT20,
includes ZVA-K4) |
K9
| Measurement of group delay on frequency converters without LO
access (for ZVA, ZVT; |
R3
| Three years of depot repair coverage, including recalibration and
test data if necessary to complete a repair - |
R3
| Three years of depot repair coverage, including recalibration and
test data if necessary to complete a repair - |
R5
| Five years of depot repair coverage, including recalibration and
test data if necessary to complete a repair - |
R5
| Five years of depot repair coverage, including recalibration and
test data if necessary to complete a repair - |
ZV-Z218
| 1,85 mm calibration kit, fixed match, TOSM male and female
calibration standards |
ZV-Z96
| Flexible Precision Cable 50 Ohm 1.85mm(f)Rugged. to
1.85mm(m)Rugged.DUT; DC to 67GHz; 635mm(25 inch); 1 piece |
ZVAB-B18
| Removable Flash Disc for ZVA/ZVB with controller unit FMR7/3 or
FMR7/6 |
ZVAB-B4
| Oven quartz (OCXO) for ZVA, ZVB, ZVT |
ZVAB-K2
| Time domain (for ZVA, ZVB, ZVT) |
ZVAB-K30
| Noise figure measurement on linear and frequency converting 2 port
devices (for ZVA, ZBV and ZVT, |
